Hello, I have a mazda 323 S 1.5 and I have to have my valves reset. How much do I have to take apart until I get to the valves? someone may have pictures or can tell me if it is difficult? please get a quick answer!
Author: 00c12f
-
State-of-the-art question
so my father wants to clean up his MX5 NA n standlight in the front. Due to optical improvements (air intakes) there are no ones in it. My question. Is it permitted as a stable simply to clean itself in a poplar fit ne super bright LED and then to use this as standable? Do they have to have a minimum height or can they also at the bottom to the bumper to be needed?
-
S-Type 3.0 (11/2000) Poles in the front axle
Hello all, I bought an S-Type 3.0 l last week. The car was registered 11/2000 and has about 145 TKM down. HU u. AU had the seller re-made on 12.10.2011, whereby according to TÜV report no defects were detected. However, the car has polter noises on the front axle, which is particularly noticeable in poor road conditions. According to the seller, this deficiency was already examined by the Jaguar car dealership in Kronberg, but even there nothing could be done openly. For me, this is hard to imagine, because the sounds are not insignificant. Maybe one of you has had a similar problem before and can give me solution tips. I don’t necessarily want the workshop to start changing one axle after the next. Thanks already for your help ! jag-jag
-
which dealer has Logan MCV-LPG in stock
hello dacia friends. since my dealer is still unable to deliver I am looking for a dacia logan MCV incl LPG ab werk und klima. the conversion costs later on over 1000,- euro more that I don’t really want to spend. many dealers offer the car ab ware, but if you call no one has a there and then comes back the delivery time of 4 – 12 weeks.
-
Make “spot repair” myself -> how do I get a repainted spot again “invisible”?
Hello guys, I’m going to hit another topic, I’m especially curious today… So I’d like to know how to get rid of the paint transitions (spray mist) after a spot repair (small repainting spot) so that you don’t recognize the repaired spot immediately. I’m very familiar with body repair work, but I don’t have any experience in making the “invisible” repaired spots. I have some scratches and small dents on my car. I don’t want to repaint whole areas of the body because of a small scratch. I just want to know how to get a transition, I know that it’s kind of sanded again and then polished, but which grit can be used, which polishes you need? Have some very expensive professional grinding pole here. ituren (3M etc.) stand, but have no ahnug what I can use for what. Oh yes, professional polishing machine and various polishing attachments (for drilling machine or similar) which are also higher speeds are available. Would I be pleased about an explanation! Greeting gap
-
Underbody protection and varnish sealing
Will the TT probably also drive in winter. Are underbody protection and varnish sealing important or recommendable if you want to drive the car longer ? Or is it at least well enough protected below ? Which varnish sealing do you recommend ? First of all thanks.
-
Active woofer goes out at too high loud strength
Hello together, I recently installed an eton move m12 400a, so far so good. However, if I turn up the loudness there is more exposed and if I turn on louder the sub goes off. The power lamp still lights up and the protection lamp does not work either. I have tried it with a high low adapter, also can not. I connected the sub to the rear boxes, because it did not work at the front, because the sub only played very quietly. Abe r when I put my fader completely on the rear boxes and thus the front no more sound of itself I can fully turn up and everything works so I don’t think it can be a current problem because the voltage at the woofer I measured and there everything fits. Maybe one of you has an idea what it might be. Lg Flo
-
Belt warning device Passat 3c
Hello I need help to deactivate the belt alarm. My daughter’s car was a Passat 3c 2.0tdi Ez.2008 I wanted to deactivate the belt alarm as with my vehicle.I had a long coding and all the steps were explained.The coding with my daughter is 160F00 In her control unit there are however no hints to change the coding.How must this coding be changed so that the belt alarm is switched off.
-
Reset Audi Multitronic
Hello, I have an Audi A6 s.u. with a MT that makes a bit of a bitch. I was recommended to set the adaptation values to 0. Was then at AUDI and asked the question. He thought I should do another MT diagnostic, if there was something broken, one could use Kulanz and so on. Can I put the adaptation values back with 0815 interface and VAG COM software? If so how and where do I do that? I prefer to AUDI? Stephan
-
Vision New York Pollutant Class Euro 1-Euro 2
Hi has to take up the topic of retrofitting from Euro 1 to Euro 2 or higher today. It can’t be that in this country there are 2 different invoices for the Chrysler Vision (assuming also New Yorker) regarding the car tax classification. I have been watching now since August 2005 in eBay for how much the visions are always sold.Now 3 pieces have been there since that according to the providers had Euro 2 standard. I asked for one. because he is not the owner.I should then be called by an acquaintance of him who knows himself there.No one has registered.I only experienced so much,Zitata is built in then you have to drive to a Chrysler workshop (only the original Chrysler stamp is recognized) and then you get the Euro 2 entry.At 2. where I asked (about 3 weeks ago) it was so that the entry was already from the beginning in the papers. I have asked for the copy of the vehicle registration or letter to at least bother my Chrysler dealer because he can (or does) not help me either.Of course, he won’t get anything.With the usual manufacturers (Twin-Tec and so on) there is always the same answer: the 3.5l engine is too rare, therefore there is nothing for it. Who knows advice ? Who can help ? How is it with the successor of the 300 M which has nevertheless Euro 2 you can use Is it something to install? Or should they have fooled me from eBay to get rid of their visions? Greeting visionary