Category: Nissan Micra, Note & Pixo Forum

  • Rugging at full load start

    Moin Moin, I drive a Nissan Micra k12, bj 2006, 1240 ccm, 80 hp, 223000 km. When starting with load, i.e. if the most gentle pedal kick is not being hit, the car breaks. Mainly in the range of 1500-2500 revolutions. This runs through all gears. Due to the feeling of lack of force lock I wanted to change the clutch today. However, the workshop staff said that this is intact. This is also unlaudable, because the switching processes are clean and partly a clean pull up is possible. Especially in the morning, i.e. with a cool vehicle, there were no restrictions. It is now assumed that a sensor, the control chain has also excluded the workshop master. However, he could not yet tell me a concrete idea. The car goes to the workshop again on Wednesday to read out. Does anyone have an idea in which direction the search should go? VG and many thanks already in advance in advance.

  • Micra K 12 vehicle does not start by ignition key, only with push it starts

    Hello Nissan municipality, our Micra K 12 1.2 Year of construction 09/2006 does not start with the ignition key. If we put the key in the ignition lock the control lights on but at the start position nothing happens anymore. If you push the vehicle with the ignition on the ignition on the car starts immediately. But I do not always want to assume that, therefore I have already changed the ignition contact plate here in the forum today. Unfortunately, the exchange did not bring any change to the situation. Maybe one of you still has a tip where I can start now, before I still have to bring the car to the workshop. I assumed that the immobilizer is in order because the car starts with the push on, which would probably not be possible if the immobilizer was defective. M.f.G. Andreas

  • Motorists don’t go out

    Hello Schrauber Gemeinde, I have the problem with my Nissan Micra K13 Bj 2011 80Ps 44tkm that the engine light (diagnosis) does not run out after the start. The vehicle runs, starts well, and you feel nothing when driving. Have read out the error P0011 camshaft “A” adjustment (bank1) camshaft position faulty. Errors can not be deleted. I could already have the repair done at Bosch because in the workshop my brother is the head. Now my question, someone has already had this error, or rather I would be interested in “if yes” what experiences you have with Nissan Workshop regarding the error diagnosis of the procedure for the repair, and also the culant claims (e.g. percentage share for covering the repair costs) I will ask the box next week to Nissan and listen to what they say. Greeting

  • >Buy car battery for Nissan Micra K11<

    Hello to the motor talk round! Unfortunately, my installed Bosch car battery has today “joyed” (the car doesn’t start anymore, electronics don’t make any noises) and I would like to save a few euros, like to make the battery change itself. Unfortunately, there is a large selection of car batteries for the Nissan Micra K11, so I find it hard to choose or I don’t know which one fits the car at all. Does anyone like to help me with the jumps? any support. LG Shinbo87

  • Nissan Micra K12 2010. Extend rear light to replace light bulb – PICTURES-

    Brake and driving light at the rear left the lower bulb was defective and the tail light was removed. All this is done when the rear flap is opened. Do not try to go over the inner lining. First unscrew the two screws and then with feeling also loosen the left side of the tail light by jerking. It is clicked there and I marked the pen red. In no case somehow go in from the side with a screwdriver and the whole levering as well as in many YouTube video Then unplug the plug. Then remove the black sealing mat and remember the position. Click the lamp holder also over the red circled area. In the case it was the lowest light bulb. Replace and rebuild in reverse order. As said, pay attention to the correct position of the seal. Total construction time 5 minutes

  • Nissan Micra K11 Bj.98 does not inject

    Moin people, I got a 98 Nissan mica k11 with 1.0l 54 ps from a friend. I want to make him run now of course. He has fuel up to the injection nozzles. Ignition spark is there. Petrol pump runs and promotes. Immobilizer unlocks , immediately ignition is on. He just doesn’t want to inject. What can this be? Engine went out during the ride and then did not jump again. Hope someone can help me. Greeting Fabian