Category: Peugeot 4er, 5er, 6er Forum

Moin guys So again have a Peugeot just this time a 508 / 1.6 HDI with the 9HL machine from 2011 with 11200 on the clock. the box has a Macke error code 1351 so glowing candles or relays the candles I got out today and measured by all four moving at 00.8 00.8 01.0 0.15 mmultimeter was set to 200 is the ok so ? relays over ? are the two relays ? and where are the ? can you also measure yourself ? first have to grope me back in the diesel and ho ffe you can help me workshop is not in at the moment, because everything has to be here (living in Spain) thank you from the ” lookdown” Andy

Good morning everyone together and happy Easter! I hope I’m helped here. Although the following is the case. I’m currently driving a c-class 2008 switch kombi and now something new should come. I really shot myself into the following vehicle, but I don’t want to buy anything with pink red glasses and then possibly regret it. It’s here: Just found at #eBay Kleinanzeigen. How do you like this?https://www.ebay-kleinanzeigen.de/…/2078229371-216-0878?… but become a diesel. Hope you can still say something… What should I know about “illness” or something like that? I would really like constructive advice. Thank you!

Moin, I have collected some questions, because after each action a new error occurred again. 1. With our 607 the motor runs quite unevenly and also the turning up in the empty run is very sluggish. The 3rd injector has already been changed, since the quantity correction was 159%. After the exchange, however, this is still 159% (photo). Do you still have to learn or register the injectors? 2. The measurements in the control unit for the charging pressure are both in empty run on ambient pressure, as well as in the higher empty run with higher pressure should still be at ambient pressure (2 pictures). In addition, the air quantity on the rear bench is much lower than on the front bench, as well as in the empty run and in the higher empty run (just as 2 pictures). In the higher empty run this is even lower. I conclude that the rear turbo has to be stuck, since otherwise the air quantity would have to rise with and not fall off, so that the front turbo practically blows into the rear and thus the air mass falls on the rear suction path. Does someone have a different explanation for, or can I understand? The deposited errors in the control unit match the measured values. 3. When jerking in empty run, each jerker comes with a “gong” of the high pressure line between the pump and the distribution pipe. When damping with the finger, the noise is gone. During the cut-off test, no paint or vibrating of the fuel pressure valve was heard/feeled. that is related to the noise that the fuel pressure becomes too high and thus possibly also the injector correction factors hang so next to the track? and if so, is the pressure valve integrated in the pump or can you exchange it separately if necessary? Thanks in advance for replying, Lg Dominik

Hello people have had the following problem since weeks the problem that my motor lamp comes back after deleting the errors. Peugeot 607 bj 17.02.2005 – 3003 591 – VF39UUHZJ92204354 Error codes.: P0104 Flowmeter signals too low airflow to the rear cylinder P010F Flowmeter Signal imbalance between the 2 airflow sensors P0404 front cylinder AGR valve circuit valve position too far from the refractive value that would be sometimes the most important one LMM changed other k ommt the days was residue, and the front AGR valve also NEW What can I still do ??? Can you help me ???? And then I still have problems with my chassis error code C1155 signal springer front right. Interruption or curvature to mass C1157 signal springer front right Coherence of the further tells me my wiper water always it is empty every 2 day ;-( although full or not empty …. all faults is on it Constant and almost what forget my tail flap pe goes on electrically but doesn’t close with the red button itself anymore – maybe even ;-)) I would be grateful for any help Lg Dominic

Since October 2008 I have bought a 407,SW with 100 kW (diesel) the car from a Peugeot dealer with warranty. Km stand 48000 on purchase. At 56000 km a clutch slip occurred. A clutch wear was also determined by the dealer, which meant that 811 € were due. On my driving mode the wear was certainly not. So a new clutch was installed and when I picked up the car I was told that the front shock damper They also have to be changed. One was also surprised that I hadn’t noticed it yet. I then went to ATU and asked if they could replace the shock absorbers. However, there are no shock absorbers for the 407 at ATU. My big worry is, if I have the car repaired at Peugeut, that are possibly used original parts of Peugeot, which make the problem a repeat factor. Of course, these are “wear parts”. Can anyone tell me if there are shock absorbers at the front for a 407 SW, which are not produced or purchased by Peugeot? I don’t want to pay 360€ every 2 years. With my VW the first after 230 000 km were still in order. Then my second concerns: We want to go on holiday for the first time with the 407 SW with our caravan (1360kg). Is the car able to overcome larger distances n ? I mean the clutch is then certainly heavily loaded. Does anyone have experience with the caravan operation with a 407 SW diesel? many thanks

Hello dear mechanic, and the following has happened. (Auto: Peugeot 407 Coupe 2.7Hdi BiTurbo) I got the error message exhaust system defective (without emergency run) with engine control light. Was then with a software optimizer who knows nuts and asked him if he could make an Agr off + Stage 1 software. Said done after 10 different software he had no desire any more. He flashed me the “original” up again. I then completely frustrated home. The first 200m switched the Aut o immediately into the emergency program with the error message: counter speed defective. So I then of course completely overburdened. Car only turns up to 2000u/min Then I drove the next day (today) to a very good tuner of which I heard a lot. He flashed me a software with Agr and stage 1. MKL was gone and the error exhaust system also gone. Only the error with the electr. G has remained defective. He is still in emergency run. We tried everything that was in our power, unfortunately without E Rfolg. Because he is an autoelectrician and doesn’t know Peugeot so well. Can someone please help me? I’m really desperate…. And yes I know Agr off does not correspond to the StvO. I would be grateful for any answer.

Hello Peugeot friends, have an annoying problem with my lions. First of all to the car. It is a 508 built year 2016 with the 2.0 Bluehdi engine 150hp. The car has currently 107500km down. Chassis number VF38DAHXMGL006707 The car has stood for 1 week because I have changed registration marks and I was traveling with the other car. On Saturday I got into the car and had to find that the car has vibrations with running motor. The whole car is on the v The vibrations occur in the empty run and also when driving in the range of 800-1600 turns. After that they become a little less. That’s also really exhausting if you drive in the local area with 50 or if you drive 30. Because then you have constantly these vibrations. Before I left the car, I drove 1000km autobahn per week. And since nothing vibrated or anything else. Just everything palletti, only now after this one week of standing these vibrations. How out of ghost. And they don’t go away any more. Somehow it seems to me that something on the two-mass swing wheel was saying goodbye. But is of course pure speculation. Have you ever heard or had something like this before? If someone had access to the spare parts catalog. Could someone find out everything for me for the reperture of a coupling? -Wave sealing ring swing side -Swing wheel -Print plate with clutch disc -pressure bearing -screw flywheel on crankshaft -screws pressure plate on flywheel Thanks for your help positions.

Hello, I drive a 407 Coupe 2.7HDI , the equipment is the one with the fabric seats. Seats are manually not electrical. I wanted to convert to leather seats Electric with heating. My question is whether the plugs from the airbag fit.

Hello, I have installed the technology of the 407 (2.0 16V, RFJ 103Kw = 140 HP) in my PGO Speedster. Now I would like to adjust the valves. Some say, however, that it is not necessary/possible. That would mean that the hydropumps are installed here. Is that so? Karl

Hello together, since recently I am represented here again at the Peugeot Forum. About 3 weeks ago I bought a Peugeot 607 2.7 HDI FAP 205in black. Year of construction 04/2006, 172,000 km run, from outside and inside very good condition and good equipment. 8 compartment tyres on aluminium rims with still great profile. TÜV still up to 06/2021. Vehicle history is clearly understandable. 6 months the car was admitted to a Peugeot car house and then the car was approved by only one owner. The Corona virus caused me to transfer the car 3 weeks ago and could only register it on 08.04.2020. On 14.04.2020 the engine control lamp started and the following errors were issued: – Exhaust gas system defective – Suspension defective Off to the workshop for error reading. According to the workshop there were so many errors in the memory which was not clear which was now the real error. First the memory was deleted and further This was yesterday on 15.04.2020. Same error: – Exhaust gas system defective The error message of the suspension was no longer displayed. Again in the workshop, error read out. Result: – Air quantity meter broken In addition, you had the car on stage and I saw it with my own eyes what is in the trouble: – Engine from below very strongly oiled. From above this could not be seen. Where exactly this comes from you have to look more closely. ar now no time. – Axle cuff in front right broken – track rod head in front right broken – suspension in back is a bit broken. So small bars, therefore the error message. I was quite baffled. I had looked at the car very carefully but did not have the possibility to take the vehicle on stage. Test drive went very well without noises or incidents. I called the dealer and he said this once internally and reported himself but he only got the car bought, washed and put again for sale on the farm. Free according to the motto. Bad luck had, since he has not earned much on the car now to do still expensive repairs at his expense. Do you have any tips for me? Which costs would I have to reckon with? Turn on legal protection? Thank you already.