hello, what loses an engine on PS when the 200000 Km has run ? you can of course not say on the basis of a faus formula, because it always has to do with how the engine was treated, but so about ? have a C20XE with 206000 Km thank you !!!!
Category: Smart Forum
-
Differences C20NE Housing Ventilation
Moinsen, some time ago I mentioned that there are obviously 2 different vents on the C20NE. Since I wanted to ask more about a new thread (with new questions ). In the appendix you will find a picture of my built-in housing ventilation (C20NE Vectra A, Built. ’91) and the valve cover, which I now have here (Astra F GSi, Built. ?) My question… the second valve cover from the GSi looks much more useful for me, since only the first venting looks much better for me. I’d like to change my head on the outdated GSi head with its valve cover. Where would the additional ventilation theoretically go, and to what extent could I convert the existing ventilation to the thicker & additional ones? What do I need for parts? I’m grateful for all tips & tricks. Greetings, qp
-
Chiptuning C16NZ
What does it actually do and what is it to think of the 15,- Euro offered at ebay of “tuning-exe”? The ratings speak for themselves, but do people imagine that or what is going on? Here’s the link.
-
C20NE camshaft wheel to early???
And another question… I made timing belts with my car (C20NE). I found out that the camshaft wheel was a gear direction early. If you set the ignition to early, the engine should be bitten in part. But how is this when the whole camshaft including the ignition distributor is moved towards early? Has there been any experience???
-
valve damage astra g 1.6 16v
Perhaps someone knows advice: opel atra g 1,6 16v bj. 98 cars is consistently checked book maintained. is always driven with brand sprite (super) on the highway sudden performance loss at approx. 180km/h, right approach, engine tuckers on three cylinders but runs. to atu, no compression on the 3rd cylinder at approx. 114tkm, valve burned, outlet valve, 3rd cylinder new tooth strap, water pump, tension roller (was almost due in turn), valves, cylinder head seal and new ignition candles on the road autobahn sudden loss of performance at approx. 180km/h, right approach, engine tuckers on three cylinders but runs. to atu, no compression on the 2nd cylinder at approx. 118tkm, valve burned off, outlet valve, 2nd cylinder does not tolerate higher speed or speeds from a certain running power? problems with continuous load etc.?
-
2.2 bj.2001 no gas
Omi 2,2 16V caravan nimt no more gas on turn. goes up and down alone what to do, was at atu with the because I stayed there. the tell what of three causes that can be throttle flap, LMM and so on. who knows rat
-
Omega A runs like a sack of nuts
Hello. Omega A, Bj 93, petrol C20NE. Since last Friday my box has been running worse and worse … At first it jumped on but then ran like on 3 cylinders. When the Bock got warm, the car ran almost impeccable. In idle run, apparently, a cylinder dropped off every now and then. On Saturday, the (warm) buck ran out in the city during the ride. Only after 2min he jumped again and then ran ok. This morning he jumped on and went off. Then he jumped on but very badly. The MKL is out. Totzdem read out nothing in the memory. Candles and fuel filter changed. Fuel hose pulled off at the gallery and torpedoed for about 6 sec. It comes but fuel only about 1/3 liter. Normal ? Besides, I fell on that I had no pressure on the system when pulling off the fuel hose. Fuel hose again. Started. After that, the bock ran tip-top for two minutes and at once in the Lee Rlauf started it again as if one or two cylinders were exposed. Ignition light gun on each cylinder and I have dropouts on each cylinder. Hmmm …. Do I have dropouts because I don’t get fuel or too little pressure on the system or do I have ignition dropouts because the ignition distributor/cap is fertisch? The distributor sits on the camshaft at the spray wall and is secured with 3 Torx screws. How can I get there? There is no space. With a nut and 1/4″ ratchet goes d a nothing. Can the distributor cap be pulled off when the screw is loose?
-
Phototechnical report for Cadillac Catera taillights o Reference for registration sought
Hi dear Schraubergemeinde… as you can see at my FOTO I have installed the original us Cadillac Catera Heck, but now I have to register it, and I am astonished how difficult this is in our German state…. 🙁 Some say without a light engineering report goes nothing because of registration, since the lamps are Made In Germany, but without e-marks, The others say a continuous lamp may not exist in Germany, etc …. someone has ideas, experiences mi t the topic ??? please listen to each other and tell me, I am almost perplexed…. thank you in advance…. mfg Töppy
-
Cover windshield
Hi guys, after the winter is here now, I have to think about a cover for the windshield. I prefer one that also covers the gap between the bonnet and the windshield to get the snow out is not funny ?? Which windshield covers are used by the other lantern parkers here? Thank you and hopefully the summer will be back soon Peter
-
Several questions
Hello, I have several questions today, but I don’t want to open up so many threads. 1. How do I know if I have an electronic (or possibly no or defective) livau regulation, in which manual I know that this snap has to be on the re. taillight. 2. My climate is not running, I think. Problem: the function light (so the small point in the switch when the light is working, however when I turn on the climate no indicator light, the same problem If the climate had been changed, there would be a sticker in the engine compartment (refitted to R134a) and if it had been laid still(?) there would have been a sticker. 3rd time a theoretical question about the Lambda probe: Can I draw a conclusion from the exhaust gas values in the AU protocol whether the Lambda is slowly approaching its life-end? The limit value for the Lambda is 1,030 or so. Now I took the old test report (2006), there is the Lam bdawert 1.015 and the present value is 1.025. Should I prepare for the change? Thanks already in advance