Category: Smart Forum

Hello everyone. This is my first post, so forgive me for missing information and like to ask. I have a problem with my girlfriend’s Opel Adam. It’s the 1.4 with 87 hp (Z16XE). In addition to the code 89 displayed in the on-board computer, the radiator fan runs at the highest level as soon as the engine is switched on or the code appears in the AI until the ignition is switched off. I have already checked a lot and am now at a loss. I have used a simple ELM327. I have already checked the following. I have carried out the measurements both on the sensor on the thermostat and on the cooler. – Visual inspection of the plugs, pins and wires of sensors and ECU for damage or similar – Resistance of the coolant sensors at ambient temperature (25°C) and operating temperature (80 °C). For comparison I have taken a new sensor. 55591401 from Febi/Bilstein) -> Plausible values and small deviations – New Senso – Power supply sensors ~4,99 V – Short circuit between signal circuit and power supply B+ checked. – Through measurement between sensor plug and ECU (both lines <2,0 Ohm) - Through measurement between both lines to exclude short circuit. I changed the coolant about 3 months ago and aired the system. Therefore, I exclude air inclusions. However, I would have this often you The cooling water is not completely clean. But therefore the error m.M.n. should not come. Please correct me if I am wrong. Does the sensor on the engine give the signal to the AI and the one on the cooler is responsible for the engine control or what is it like? Maybe I should focus on the sensor on the cooler again.. I really don't know any more. I don't think the ECU is defective, but I don't know what else to check. Therefore my Anmeld Thank you for your help.

Hello people need your help my Adam 1.2 -69 HP Bj.13 no longer starts. Tank is full the display of the tank shows empty on -battery new -the starter turns but no mux. where sits the petrol pump has the one fuse where the sits. Is there a gasoline sieve. Error read out =0 control chain renewed last year. I was refueling and at the gas station he did not jump on – so ADAC-nun he stands with me in front of the garage. I am grateful for every tip

Moin had an event enough Sunday. I only helped a buddy in a move and on the way back my wife calls me and says she can just be towed from ADAC to the next stop for 350€ because her Opel would be loud and the error message oil pressure came off low immediately engine. So we went to the rest area and towed her 60 km home. At home I immediately put the OBD on it. And it came the error message P0011 Timing camshaft. So briefly read and it seems What only worries me is that it also makes extremely loud noises. Can something be broken now. What makes it worse? She had immediately turned out the vehicle. Did you already have problems or experiences with it?

When changing to winter tyres, the menu item for learning is not available. If you call up the tyre pressure indicator, only strokes are displayed for all four wheels. When pressing the reset button on the left steering wheel switch, nothing happens (even after 1min). However, the reset button works in all other menus. In this attempt, the ignition is switched on, the circuit is in idle, the hand brake is tightened. We have played around with all these switches, the Menu item doesn’t come. See photo. Of course we didn’t want it to be true that it’s on the menu, so we also tried the following: – Activating the sensors using an activation box does not bring any change – A nearby summer tire is shown again after activation – driving around 20km with over 40km/h does not bring any change – the question whether the tires at all answer to the activation is clearly with yes to answer, you can answer the signal listen to the radio frequency 433,92MHz – yes, send the tire sensors It seems to have nothing to do with the activation of the sensors, it is only not possible in the tire pressure indicator to reset the learned tires.What do we do wrong? How can one reset the learned tires? Thank you and always good ride Volker

Hello everyone, I’m new here in the forum. Would like to welcome you all first. I’ve been driving a Opel Adam since August 2016. I’m very satisfied ….except two months ago ….there the tank display didn’t work. I read on the internet that the problem is known at Adam and Corsa….then drove to my OFH…. He then read out the error and changed plugs…should go to Kulanz according to OFH….after two weeks I got a Rechn …the request for financial support was rejected….then again submitted a new application to the Opel Customer Service…rejected….have filed a complaint with the Opel Service….which referred me back to the customer service….can anyone of you please help me? my question to you ….who had the same problem with the Adam? and were the costs of Opel taken over??? how would you proceed…. am really mad. since I cost you the problem at Op. I thank you already in advance for your answers. L.G. Schnubbel13

Adam Cross – Bj. 2/2015. Lt. Workshop inspection is to renew the clutch. Almost 50,000 down. Do I have to thank my way of driving. What costs should I expect? Thanks and greetings

I was on Friday with my little one for the 1st inspection. And then around 249,00 EUR poorer: inspection 1.1 hours: 97,90 oil filter: 14,21 engine oil 4 x: 80,52 system active ingredient BENZ: 12,56 1 O-ring: 1,09 and disc clear: 3,70 together: 209,98 + fairytale tax 249,88 I find this quite violent and have the feeling that the guarantee extension given during the purchase (but only effective at inspection in the house) is fully added to the inspection price. Does a complaint with Opel possibly pay? Thank you

Hello! Betr. Adam , EZ 5 / 2014 manual gearbox , UJN system Already dealt with several times in the forum but never communicated a solution , unfortunately Therefore , new topic , with a ,, final solution ,, sorry I never come into the menu , want to calibrate them , When displaying , , tire pressure indicator , , goes no further therefore my post Everything carried out according to operating instructions u no success wheels were already mounted ( Org. LM 7 x 17 ) In the menu tire pressure also no pressures are displayed , see Annex FZ w urde 2 weeks ago bought from private. (seller has emigrated) Hope someone can help me Ps Have already learned some Opel models u had never a problem