Category: Smart 1 & 2 Forum

Hello have a problem with my Smart 451 year 12/2007 1.0 71PS 113 TKM the first few m drives and switches the car perfectly, then it goes on fault and it switches e.g. no more into the 3rd gear and the 1st gear. Or with a new ride no longer into the 5th gear neither manually nor in automatic mode. I also noticed that the error ( i.e. the fault ) always occurs when switching down. Up to now it has been renewed: The clutch actuator incl. adjustment, I checked the supply lines from the gearbox on (screwing positions etc.) the GSG looked at me, as far as everything normal and nothing eye-catching. Error codes were read out : P1903 Switching process implausible P1800 Adaption Faulty P0914 Switching control P1901 Switching process P1801 Gear control P0914 Gear selector sensor These were all errors that were saved and also after the error imer appear immediately. Now my question: clutch? Switching motor? Gears? Am I already making a beautiful Sunday tomorrow and expanding the gear, however, I probably have to remember the fact that Sammy will not be able to see your fault.

Hello, the interior lighting of my Smart 451 ED3 doesn’t go off by itself. It can be switched on and off by a switch, and the switch is in the right position for the automatic shut-off. Nevertheless, the light still glows brightly, no matter what I do or how long I wait. A manual inspection of the lid lamp did not reveal any obvious errors. I suspect the SAM does not implement the automatic shut-off for whatever reason. Can it be due, for example, to a faulty door contact? The central locking works without any problems. Thanks for every tip that helps me to circle and fix the error source more accurately.

Have a Smart again as a project. A 2000 he 45ps Unfortunately I am not the first hobbyist on the Smart. In the engine compartment I discovered an empty plug connection close to lid fitting. Who can tell me what is missing there. My intention is to make the Smart completely in a well-kept factory condition.

Dear Smart Friends, since the IsoFix system is not only more comfortable but also safer for the child, I decided to have the “system” (IsoFix “Stange”) installed afterwards. The shock was great when I was asked to charge almost 670 EUR for it (and that without airbag shutdown)! The friendly explained to me that you have to change the seat cover completely. Why, he could not tell me. According to the installation photo, it was only 4 screws (!) needed to install the bar. A call to Fismatec solved the puzzle: Smart builds a “recognition system” into the seat cushion, which switches off the passenger airbag as soon as an IsoFix child seat is connected. Because my Smart has an airbag shutdown and I feel so a “recognition system” for absolutely unnecessary, I ordered the bar (incl. screws and covers) for 90 EUR and get it in a very short time. The rod is actually attached only with 4 screws and mothers. The holes are already present. As soon as the rod is attached to me (see a photo from ED.

Hi guys, I have a little problem and I bought Smart and at some point we had to take off the battery, whereby now you need a security code on the radio because I didn’t have, because no manuals were given. I’ve already taken out the radio once to get the numbers from the radio, maybe someone could help me find out the security code. (0000 and 1234) have already been tested.

Hello together, at my forfour the following has happened: – Grinding noises at the rear right – Workshop says: “acoustic wear indicator” – Brake disc and pads on the rear axle completely changed (at km-stand 102.000) – drive every day single ride 50 km to the job (45 km highway) – the day after brake change again to check with the mechanic – rim at the rear right with high temperature – no grinding tracks on the brake disc – wheel turns without problems plett “free” – vehicle on brake dynamometer –> no problem fixable – On the brake disc I see from the middle ( hub) starting a ring of about 10 mm wide with initial color… – Workshop says: there is the possibility that the brake caliper “hydraulically does not go in neutral position” – recommendation change caliper… – mechanically the caliper is absolutely smooth and functional – ride now for 3 days without problems, also the rim has no increased temperature meh r.. – yet I have a “mumble feeling”… What do you think, should I have the brake caliper changed? Greetings 44cdi

I raised my winter tyres last week with my Smart, thanks to the many instructions here in the forum no problem. Now I read, because I want to change the WR also with my golf always what centrings made of plastic/plastic which are probably mandatory with the Golf V, if one installs an accessory alufelge. Is there such a thing for the Smart also or is simply the summer bike put down and then the WR on it? Was there no problem with me. PS: I still have one question, I h no problem to solve 10 screws with a normal ratchet and then turn out with the hands, but with 2 screws I had to use the ratchet completely to get the screws out, while screwing in the same problem, the screws went incredibly hard compared to the others, should I change with the problem to SC? And what will they tell me, if I want to do this on guarantee (EZ 04/09), because I did this myself with the.

Hello dear smarties, am new in your community or wants to become it. Since I am a professional commuter (100km/day) I thought of convertible, economy and less value loss/a than with my family coach (C Klassebj 2008). I don’t really care about the km of the smarties, have 2 favourites. Important to me is: CDI, SHZ and Tempomat… What do you think of this? Too many km? A normal car diesel has just arrived…http://www.ebay.de/…/140934256524?… Would you be very grateful for your advice!

Hi Forum, I’m happy to be with a Smart Convertible, because I wanted to get some opinions from old-fashioned smart experts before! Does something speak from your point of view against this Smart? Click Or better that? Click Thank you for your help… Stefan

Hello together, must renew my steering angle sensor. Can someone help me whom I need for a 451 BJ 2008? Would this fit purely theoretically or does it have to be exactly the sensor from the series?http://www.ebay.de/…/251615522620?fits=Make%3ASmart If yes…does anyone possibly have a link at hand or could tell me what the part officially costs at Smart? Thank you!