Category: Werkzeug Forum

Hello together, I am currently busy building a larger hut / hall (approx. 100 m2). The floor should be paved. Since I plan to buy a lift (only for hobby purposes), I would prepare a foundation (strip foundation?) in the course of the construction work. Are there standard dimensions for the foundation to which I can hold myself? Doof is of course, that I am not yet at all aware of which (used) 2-pillar lifting platform it is used. or are the dimensions similar to those of the different manufacturers? VG Markus

Hello Forum, which coating or floor covering have you installed in your garage or garage workshop? Since I am about to build a new one, I’m about to inform myself. What about 2k epoxy resin coating to hold? I wanted to let the floor flow first, but the 2K coating sounds very good. Especially resistant to oil, cooling water, salt, dew water etc and above all plasticizer resistant what the tank room colors are not. Your tips / ideas?

Moin, I’m just wondering, if I turn a screw (before oiled, 6mm) with a cloth grease free, and then into the thread with screw securing e.g. Loctide middle-strength, is the screw then secured? although the thread hole is oiled inside, can be? or if I make the screw (before oiled) fat free, clean with brake cleaner, and then wipe with cloth afterwards, then screw securing Loctide middle-resistant up, and in the thread hole also clean brake cleaner he (can I not wipe off) is the screw secured? I just changed the cooling water flange at my golf, which is sitting at the engine block, therefore the question, which I wanted to secure the screws. Sometimes you can not clean the threaded hole… Does screw securing also, when I have prepared brake cleaner, and then immediately turn the screw securing after, so the screw with screw securing. How do you see this??? Holds screw securing at the “nassage” brake Cleansing?

Hello, have at a Geodyna 5501 the problem that the rim diameter is very often detected an inch too small, i.e. 14″ instead of 15″ or 15″ instead of 16″. If I turn the gear at the poti a point to the left or right, error message E3 is issued, i.e. the resting position is wrong. So that seems to be too much. Does anyone have a service instruction in which the setting is described? The instruction also does not have to be to a 5501, all models with the inner T Astarm should fit.

Hello together, for the maintenance of the charging device shown below, permanently plugged on the battery of my motorcycle. since yesterday the diode no longer lights up. how can I measure with my multimeter. whether the device still works? what value should be displayed via the plug? for a short (and idiot-proof) description I would be very grateful and wish you all a beautiful Sunday mark

Hello, I’m looking for a 4 column lift, best with axle lift, which doesn’t have to be anchored and fits into my garage (ceiling height 2.24 m). Would like to use this mainly suspension components in normal position and possibly make track and fall adjustments in the distant future. Had contact with Twinbusch, but unfortunately they have no matching, due to the low ceiling height. Do you have anything suitable for me? LG Dignitas

hi! search a roll lying like this https://www.kaiserkraft.de/…/?… but maybe half as expensive. does anyone have any idea?

Hello, I have a problem with my lift CO2.35 (3.5 tons) Two-pillar lift, this is exactly identical to the Maha Econ 3.5! Three years ago I bought the lift and it somehow never worked properly! If I lubricate the guideways from the lift sled and the nuts with the original grease then the lift lifts about 3 weeks normal only then it starts to clamp again and again so that the electronics shut down and you can only drive down! And d I have already replaced spindles and lifting nuts with new ones because I thought that I had used the wrong grease at the beginning and that the plastic molds were damaged! Unfortunately, this did not change anything either! I had no guarantee because I set up the stage myself! Of course, according to instructions in light V form! At Maha I have already asked them, however, they can not really tell me why should be due to the problem! Maybe someone had the same problem, and can help me? Thank you very much!

Servus! Yesterday I got a Hoffmann Geodyna 88 at a reasonable price. Dan device is complete as far as possible. When switching on it shows an error code E48. My questions are: – What does the error mean, what damage does it indicate and is a repair possible? – Where can I get a manual and a repair manual? – Where can I get spare parts if necessary? Thanks in advance for your efforts and nice greetings! Helmut

Hello I am looking for a page or an app A program where it is specifically about auto repair and its instructions there is such a page or a program. If someone knows programs that can also be downloaded easily I would be happy about a message