Category: Werkzeug Forum

Hello together, does someone have a good idea how to illuminate a double garage optimally? Currently, a fluorescent tube is attached to the right and left side, which is of course much too dark according to today’s standards. Do you have ideas for me, what kind of luminaires you could use? The basic conditions are: – Daylight lights (6000 to 8000 Kelvin) – Very bright to work in the garage – No special lamps for which you can no longer get replacement lamps in 5 years – Energy efficient (LED?) – Humidity and dust resistant – Price 200 to 400 euros in total for everything

Hello dear colleagues I have always cleaned the gratings on the rim support by hand during the spring/autumn tyre change. Now I am looking for a somewhat easier machine cleaning option e.g. with a pot brush for drilling machine or small flex. I don’t want to lubricate or paint on it, but just clean it without damage. I assume that a strong steel pot brush is too aggressive. I find e.g. pot brushes made of steel with brass stratification would that be okay? Or should it be pure brass, if there is such a thing with pot brushes? I ask for a recommendation from people who know about it. Thank you in advance! Greetings from weather

Hello to all car fans I would have asked you a question, and I am looking for a good shear cart lifter but which is good from the quality, I had already tried a Heyner with 2 tons but the tilts too easily and has too much room for manoeuvre in the joints although the one is praised so high at Amazon but that is so bad that the thing is dangerous. I have seen on the Internet of SW Stahl there is a shear cart lifter but does what, the shear cart lifter should hal t so about 40cm can lift the vehicle up. Would be grateful for a reply. Greetings Amiwagen

Good day, I had bought the following compressor: https://www.manomano.de/p/…encompressor-450-10-100-230v-11881751?… I wanted to have a hose drum, I had decided for the following: https://ebay.us/sdADNH I can’t get the hose connection of the drum into my compressor? Did I maybe order a wrong one? In the hardware store I had bought a cheap set including spiral hose, this goes in without problems. e already differ, the Ebay Link is a bit wider. Greetings

Would like to get me a small additional mini impact wrench but now the spoilt of choice-better said the question of which really what is good in terms of release moment? The small pneumatic are given partly with 1400Nm release moment but like with the manufacturer’s specifications they always say little. I am concerned about real experience values whether with the screwdrivers also difficult cases like mounted brake caliper screws(200Nm!) or maybe even a drive shaft screw stretch-l aut Videos in the net they pack that but you never know how was helped compressor with 13er hose and boiler direct connection is present, so it should not fail. To choose the usual devices like Hazet 9012MT , KS-Tool Mini Monster, Facom & Co. or if someone has a good recommendation just another…https://www.amazon.de/…/ref=sr_1_8?…https://www.amazon.de/…/ref=twister_B07822VYGL?…https://www.amazon.de/…/262-4983936-8380842?…https://www.amaz on.de/…/ref=pd_sbs_60_7?… Maybe one or the other experience with the screwdrivers

Hello, yesterday when I was installing the AHK, something quite doofes happened. I tightened the M10 screws used to attach the AHK carriers to the body, with the torque of the M12 screws, i.e. with 80 instead of 50 nM. I slipped in the line when reading…did not notice until I wanted to mount the M12… The question is: what to do? Let it go? New screws in? What to do with the thread?

Hello to each other, since I am about to have an engine change, I wanted to inform myself (hopefully professionally) what I should pay attention to. Are the things recommended for ~150 Euro? Can I get out the engine including the gearbox (Bmw) or is there the lifting height in terms of experience problematic? In fact, you also have to consider that the part is then scrap metal for me. Is placed in corner in which it dusts, because except for the one-time exchange I don’t have much more there with before

Hello, I have a Hitachi radio. Problem: It only comes when switching on from the speakers , Welcome to Hitachi Power Tools , then you see the 88.0 MHZ stand on the display and it is all quiet, no sound nothing ! The headphone output also does not work . It can be pressed and operated all buttons , just no sound . Does anyone know from there ?? Tips ? The radio has inside 2 circuit boards , have each photographed from front and back . Many looks a experienced electric motor more than me Schmorr or Brandstellen are not to be found on the boards. Thanks in advance! With successful tips for reperatur, I send a box of beer by Paypal!!

Hello, have me a Hofman Geodyna 2100 built year 1996 increased, as far as everything paletti happens when I balance aluminum rims to measure this faultless rims to measure data enter weights are displayed then glued test run and 2x ok. BUT with steel rims clearly first from ́ ́ ́ALU ́ ́ to ́ ́ ́NORMAL ́ ́ program set then enter data again and then the weights are shown to me this I then also axial strike but then at the control rotation she still wants to m very weights have attached to a completely different place and if I also bring this what you don’t actually do even then it’s not enough and so it goes on forever so I can do what I want with steel rims I never get this on NULL??? To info Calibrated I got it right before!! Hope this was right so let c14 turn then turn the kalibrie weight on it and wait until this dumpling sounds??? What can I still do n I don’t understand it quite as yes alufelgen perfectly funkionieren…Bin echlich über jeden info zusammenbar mfg Thomas K. aus H.

Good day, I screw on my car and wanted to change a timing belt now but this screw is bothering me. As you can see, I tried to grind it a little bit to get in with a ratchet or something like that. Unfortunately, even the hammering of a tork had not worked out. If someone has a solution, except welding, I would be very happy. Mfg.