Category: Werkzeug Forum

Servus, on my small off-road car are so wide poser ride boards. Unfortunately, they prevent you from getting it on a “normal” lift with such extendable arms. Or at least not at the designated places, where the included jack is to be set up. What can you do there? Yesterday I put it on such a stage with “roadways”, but the wheels don’t get free and in general you don’t get so good at many things. Car two such feisty carriers, which simulate almost something like a ladder frame despite the self-supporting bodywork. Can you put the car there? Or I had thought of getting thick rubber blocks and putting a slit on the table saw to put them on the jack shots over the body fold. And then there with the stage arms under it.

Hellooooo, I’m looking for a battery charge device which is not quite so expensive. At Amazone, the negative reviews unsure though most of them is positive. Does anyone have a good one that does not damage a battery ?? For cars of course so 12 volts

Hi, I want to lift my e39 up the back and take off the rear axle with a lot of leisure and time and free the reception of the tons bearings from the rust and revise the rear axle. But at the tonne warehouse up and left and right at the car lifter shots on bucks and off we go. Problem: My driveway, where I can leave it for a few days to weeks, is steep. About 4° to 5°, so between 7 % and 8.7%. Here’s my plan: Car with the muzzle to the top park Three such wedges: https://www.ebay.de/itm/281946666817?… One for a stamp lifter, two for the bucks. To do this, the two front wheels should wedge on both sides and that should be safe, right? Also very different ideas, if you have them.

Hello together, I am looking for a proper multimeter for the car area. It should be used mainly with the scooter and if necessary also on the car. What must I pay special attention to and what must a multimeter be able to do? In what price range should I look for? If someone here has experience or even can recommend a special device, then always with it

Hello dear Fornmembers! I bought a winter car for my girlfriend for limp €200,- without Tüv and it was necessary to make the cheap fit and to let it again nice assail. He was rust-free, for the new Tüv he needed new brake hose and new brake lines. New self-bended, good brake hose removed from the scrap yard and so the parts cost me only €30,- then to Tüv and now he has new Tüv 🙂 The Kleiine has climate, ZV, el. window and power steering, even 8 times over eift. year 2002 with 108000km! Now he gets new oil change with new air filter, new floor mats, then he is worth a few hundred euros more! Only cosmetic error, the clear varnish on the roof was shady and the bonnet in shiny black. So I bought 6 cans each with 400ml matt lacquer spray at the action market, with 3 cans of clear varnish, each can € 2.09 mega cheaply and pre-ground the whole with 240er sanding paper, then sanded with 800er wet sanding paper. Result Pfusch! Because it was better than before, but unfortunately shady surfaces, because with spray cans you can paint smaller surfaces, e.g. a fender perfectly, but large areas like roof, bonnet always cast shadows, because the can with propellant gas and the spray jet does not scatter far enough, so that always remains shadow formation. What do? For the first time I bought a professional gun set at Ebay for limp € 28,80 in a small suitcase. 1x a small gun with 0.8 nozzle for small things and a larger one with 0.13en nozzle and larger paint cup! 2* HVLP paint gun spray gun set pressure gauge cup case 1.3+0.8mm nozzles ( 253207886824 ) Then at the action market in Wiesbaden Megafunkten Streich-Acryllack 0.75 liter can for just under € 6,- water-based. So after home and 200ml mixed in paint cups with additional 100ml warm water and pure into the gun. Roof and hood sanded again with 800 wet sanding paper with hand. All well pasted off, in dry condition with silicone remover over it (the liter can cost just under 5,-€) everything wiped off, afterwards with sticky honey cloth again over it to remove dust particles. Today under my carport, side walls with blue foil 6×4 mtr. for €8,80 manufactured, the floor sifts, outside temperature 18° :-(then black matt tin varnish of the brand Spectrum 0.75 liter can acrylic paint for painting for 5,99€ bought at the action market. This color costs in the DIY market around € 20,-! Of which 200ml mixed with 100ml water and with the large quantity of water This was done within 10 minutes and the result, shadow-free, richly shiny surfaces, which are maturing when drying. The result is top! If I had had more time, the weather was running away, now it gets colder every day, I would have sprayed a filler before, to compensate for minor unevenness! But since the paint is matt, I am very happy with the result! Tomorrow I take a picture of the car and then you see the finished result! I found everywhere only those with 015 nozzles and the costs individually around the €28,- real cheap parts in the cardboard. Because I was lucky and met a car paintr there, who worked there and I showed him the set on Ebay with the HVLP technology he meant silently, buy the, which is very good and does its purpose! The HVLP-Tchnik consumes less air like the others and I get out with 3 bar pressure! My hardware compressor with max. 8 bar packed it loosely, He didn’t spit water either 🙂 But I’m going to buy a water separator for € 5,-? on Ebay, so that I always had the best result. If I had the roof and the bonnet painted with the friendly car painter, about 700-800,- Euros would have become due. So the whole paint shop cost me with gun, paint not yet €40,- and paint I still have left to spray the whole cart in black matte if I wanted! And I’m not going to tell you.

Hello! I would like to crimp a few shock joints. In addition, there are the most different YT videos. You can see that once the pliers are crimped on the left and right (intelligible), or even once in the middle. With the “middle crimpers” it seems to me that the pliers are at least significantly wider than usual or that they may have two partial cheeks on the left and right, so that more or less is crimped on the left and right again. in a small user manual already to be crimped to the left and right. Then the question would still arise, what happens with this small eyelet in the middle of the bumper connector. Does this have to be caught with the pliers or should they be left like it is? Here is a very nice picture: https://www.amazon.de/…/ref=sr_1_10?… . It is the bottom or last picture (enlarge, “internal divider” Thank you for illuminating to avoid g from the Committee: G.

Hello, I have a problem with my lift. If I want to lift the lift up, it doesn’t work at all. As soon as I make a reset (small button on board) and then press the down button for 15 seconds, it drives down completely and the LED on the control panel lights up green. If I want to let it up now, it only goes up by piece (so keep pressing the high button) and after about 20cm the stage stops and the orange LED flashes. What I still have a problem with my lift. It has been noticed that a red LED always shines on the board. I hope you can help me with this… Thank you very much.

Hello! I’m new here in the forum. I have a powerful Hofmann Geodyna 85 with error E53. Maybe someone can help me here. I’m also looking for manuals and schematics for this device. It would be nice if someone in the forum could send me the documents in pdf..

Hello, I have liquid bolt securing of Mannol and Loctite in the garage. There it also has up to -10°C. Can I store them there or rather not? Gruss W.

At Amazon, I bought the following cutting disc to cut wood with my angle grinder: “Hard metal flex disc for wood GRAFF Termit 125mm – angle grinder Multi Wheel cutting disc (wood carving disc) for cutting wood, plastic. ” After unpacking, I found no indication of the direction of rotation. As I read over and over again the warning to operate a cutting disc only with correct running direction, I asked the seller. After a good week, the following answer came: “Since about the body My question is: is this a technically correct answer? I have the impression that an answer, e.g. from China, has been translated with an automatic translation tool. The statement with the “fine grains of tungsten carbide”, and that it results from the fact that there is no clear direction of rotation, is not conclusive for me. g. Is there perhaps an expert who can make a statement about this?