Category: Werkzeug Forum

Hello to each other, I come directly to my problem and that is I have a Hofmann geodyna 3000 year 1996 in which one mouse drove her unsung and bit various cables. I have replaced the cables meanwhile but the machine does not want to trozdem. When I left them at first I had only the problem that she did not run with the closing of the lid, but only with the start button. Later I ran them again and saw that she suddenly sparked on the board, naturally My problem is now that I have no idea who will fix it for me or whom I could turn to. I just bought the machine over half a year ago and put a lot of money in it and need the machine urgently. I’m totally desperate and don’t know any advice at the moment. I hope someone of you knows who I can turn to or knows someone who can fix it for me. Ichh could also bring the machine by if it wasn’t too far away from me. Location is 87719 Mindelheim. I hope someone helps me above all I’m afraid that the costs will go to the limitless, as it is also very urgent. Thanks to everyone already in advance.

I could buy the welding device from the circle of acquaintances more than cheaply. Because the owner has passed away. The part is new and unused. I looked at the adjusting buttons once and found that only the switching from 230V to 400V and the wire feed, but no ampere adjustment is possible, as I knew from other protective gas welding devices. The operating cable is available but gives nothing. Who can tell me how this voltage adjustment is A table or similar is also not available in the net. I mean where you can take a basic adjustment of material thickness and voltage setting. Sure you could also find out by making some sample weldings.

Hello first to the community This forum has helped me many times and maybe it will be so this time too. I’m new here and I have a question / search at the same time I am looking for an operating manual / manual for the balancing machine of Hofmann Geodyna 30-4. Wuchttechnik.de(perter Starke) I will take as last option fals no one can help me here. The guide in this post “Geodyna 30-2, manual for calibration” I’ve already looked for Is this possible for Geodyna 30-4? Thanks MFG

Hello, there is something against removing the bolt on the boiler of my compressor (which is practically sitting at the “top”) and attaching a connection with a water separator and possibly an extra safety valve there? Unfortunately, there is no room for the separator where the “normal” compressed air connections are located. I would have to add a rather long extension.

Hello dear Forum municipality, As the title already says, this is about the oil consumption of pipeline oil. I recently added a new impact screwdriver (Hazet 9012TT) with the associated pipeline oil (such a small mini tank right at the back) and the oil consumption is enormous. Once tire changes and the oiler is virtually empty… accordingly everything is full of oil. Should that be so? It doesn’t bother me right now but such drinking habits seem a bit extreme especially with d the quantity is expressed in drops. Here it seems more like when the excess oil is blown out with manual oiling, only permanently. Mfg

Hello guys, I have run out of a Nilfisk E 160.1 high pressure cleaner 150 bar, warranty, no longer built up any pressure, have pump disassembled, and see there !, all the spring parts destroyed. Now I have the problem that I can not find the springs and the clamp plates or spring holders, on the internet you get only the complete pump for 35 – 50 €, only I would like to keep the original pump, and only the springs swap. Has someone experience with it, or ideas, and who knows whether the replacement pumps qua Litatively as good as the originals are. I am grateful for every answer

Moin people, from the above test system I ordered the Handpumep and only Lid 12 (should fit for Opel) then Lid 21 (should fit also for Opel) But unfortunately no one fits the lid properly. The 12 can be written down, but it simply does not close properly, so that I can not check any tightness. I tried this on two different Corsas B. Has anyone had similar experiences ? Is there another lid of this set that fits the Corsa ?

Hello, on Amazon I bought the “V2461N” socket wrench set from Vigor for 100€. I noticed only later that this tool case contains plastic ratchets. On Amazon there is then the somewhat cheaper tool case, the “V2461” which has chrome vanadium ratchets and costs 90€. Why is the tool case with the plastic ratchets more expensive than that with chrome vanadium. The chrome vanadium holds much longer than such a plastic. Or am I wrong?? V2461N suitcase with plastic ratchets is more expensive than that with chrome vanadium. k Ratchet: https://amzn.eu/d/97GeIZL V2461 with Chrom Vanadium Ratchet: https://amzn.eu/d/6tYCcis

Moin together, I have seen the days an advertisement of a supposedly German company (where the production or stealing I don’t know..). They make battery tools that come very close to Makita optically. Also the batteries of Makita fit there, vice versa of course also.GJEMAX Does one of you know that or maybe someone has already held the tool in hands? From the price m.M.n. very interesting, for the hobby screwdriver this should be enough. Advantage would also be, one k could use already existing Makita batteries and would not have so many different charging systems…. Or as a replacement buy the battery from them, for 6 Ah they ask a good price. I have with the company nothing on the hat and do not advertise for them, just wanted to hear if someone could share an experience. Greeting

It’s about my lifting platform: Hofmann MTF 3000 Problem: The lifting platform made noises on the secondary side and stopped 7x when it was up and down. Once two years ago, it only stalled 3-5x. Something has probably worsened. In addition, it made noises on the secondary side above. What I have done so far: I have now changed the head bearing of the secondary b column. Now the lifting platform no longer makes noises. I also lubricated everything and checked for smooth operation. p. Also the adjustment when both lifting sleds are on 30cm and the thorn is in the control bar did not bring any improvement. Right where I turn the adjustment screw of the DC circuit, whether in or out only the stick point changes when blowing up, but also no improvement. It still stops when blowing up 7x. Troubleshooting: My guess it is somewhere because of the electrics of a component. Since everything is mechanically smooth like all bearings is not dry everything is lubricated wu rde. – Can this be attached to the microswitches in the primary column? Which of the three microswitches is responsible for what? – Can this also be due to a defective contactor or turning switch. What should I check now how?